first commit

libraries/TinyGSM/tools/FactoryReset/FactoryReset.ino

@@ -0,0 +1,84 @@
+/**************************************************************
+ *
+ * To run this tool you need StreamDebugger library:
+ *   https://github.com/vshymanskyy/StreamDebugger
+ *   or from http://librarymanager/all#StreamDebugger
+ *
+ * TinyGSM Getting Started guide:
+ *   https://tiny.cc/tinygsm-readme
+ *
+ **************************************************************/
+
+// Select your modem:
+#define TINY_GSM_MODEM_SIM800
+// #define TINY_GSM_MODEM_SIM808
+// #define TINY_GSM_MODEM_SIM868
+// #define TINY_GSM_MODEM_SIM900
+// #define TINY_GSM_MODEM_SIM5360
+// #define TINY_GSM_MODEM_UBLOX
+// #define TINY_GSM_MODEM_SARAR4
+// #define TINY_GSM_MODEM_M95
+// #define TINY_GSM_MODEM_BG95
+// #define TINY_GSM_MODEM_BG96
+// #define TINY_GSM_MODEM_A6
+// #define TINY_GSM_MODEM_A7
+// #define TINY_GSM_MODEM_M590
+// #define TINY_GSM_MODEM_MC60
+// #define TINY_GSM_MODEM_MC60E
+// #define TINY_GSM_MODEM_ESP8266
+// #define TINY_GSM_MODEM_ESP32
+// #define TINY_GSM_MODEM_XBEE
+// #define TINY_GSM_MODEM_SEQUANS_MONARCH
+
+#include <TinyGsmClient.h>
+
+// Set serial for debug console (to the Serial Monitor, speed 115200)
+#define SerialMon Serial
+
+// Set serial for AT commands (to the module)
+// Use Hardware Serial on Mega, Leonardo, Micro
+#ifndef __AVR_ATmega328P__
+#define SerialAT Serial1
+
+// or Software Serial on Uno, Nano
+#else
+#include <SoftwareSerial.h>
+SoftwareSerial SerialAT(2, 3);  // RX, TX
+#endif
+
+#include <StreamDebugger.h>
+StreamDebugger debugger(SerialAT, SerialMon);
+TinyGsm        modem(debugger);
+
+void setup() {
+  // Set console baud rate
+  SerialMon.begin(115200);
+  delay(10);
+
+  // Set GSM module baud rate
+  SerialAT.begin(9600);
+  delay(6000);
+
+  if (!modem.init()) {
+    SerialMon.println(
+        F("***********************************************************"));
+    SerialMon.println(F(" Cannot initialize modem!"));
+    SerialMon.println(
+        F("   Use File -> Examples -> TinyGSM -> tools -> AT_Debug"));
+    SerialMon.println(F("   to find correct configuration"));
+    SerialMon.println(
+        F("***********************************************************"));
+    return;
+  }
+
+  bool ret = modem.factoryDefault();
+
+  SerialMon.println(
+      F("***********************************************************"));
+  SerialMon.print(F(" Return settings to Factory Defaults: "));
+  SerialMon.println((ret) ? "OK" : "FAIL");
+  SerialMon.println(
+      F("***********************************************************"));
+}
+
+void loop() {}